SMC薄型液压缸,日本液压缸电机数据[产品打印页面]

]资料

点击看大图

如果您对该产品感兴趣的话,可以

产品名称: SMC薄型液压缸,日本液压缸电机数据
产品型号: ASV310F-02-08S
产品展商: SMC
简单介绍
SMC薄型液压缸,日本液压缸电机数据 mounting bolts, use the tightening torques in the table at right as a guide. 7. Do not use two cylinders facing one another horizontally or vertically in such a way that their piston rods strike each other. 8. When the cylinder head side contains hydraulic fluid or is in a normally pressurized SMC薄型液压缸,日本液压缸电机数据

SMC薄型液压缸,日本液压缸电机数据的详细介绍

SMC薄型液压缸,日本液压缸电机数据
      QQ号：2880626089
      手机：17321017802（微信）
      邮箱：17321017802@163.com
      电话：021-39529829
      传真：021-39529831-8007
      联系人：杨雷
      公司：上海乾拓贸易有限公司
Use hexagon socket head cap screws
(JISB1176, strength class 10.9 or higher)
for cylinder mounting. (ø20: 2 pcs.;
ø32 to ø100: 4 pcs.)
2. Since a lateral load (eccentric load)
cannot be applied to the piston rod,
build the mounting jig in such a way
that a lateral load will not be applied to
the piston rod.
3. Make sure that the interlocking length
of the rod end thread (male or female
thread) and the mounting material is at
least 80% of the thread diameter.
4. When operating a cylinder for the first
time, be sure to release the air inside
the cylinder and the piping. When the
air release is complete, operate the cylinder
at reduced pressure, then gradually
increase it to the normal operating
pressure.
5. Since Series CHQB does not have an
air release plug, release air from other
components (e.g. from piping, etc.) as
well.
6. When mounting the cylinder body with
mounting bolts, use the tightening torques
in the table at right as a guide.
7. Do not use two cylinders facing one
another horizontally or vertically in
such a way that their piston rods strike
each other.
8. When the cylinder head side contains
hydraulic fluid or is in a normally pressurized
condition, the applied load
must not be allowed to strike the piston
rod end. Avoid such applications. Use hexagon socket head cap screws
(JISB1176, strength class 10.9 or higher)
for cylinder mounting. (ø20: 2 pcs.;
ø32 to ø100: 4 pcs.)
2. Since a lateral load (eccentric load)
cannot be applied to the piston rod,
build the mounting jig in such a way
that a lateral load will not be applied to
the piston rod.
3. Make sure that the interlocking length
of the rod end thread (male or female
thread) and the mounting material is at
least 80% of the thread diameter.
4. When operating a cylinder for the first
time, be sure to release the air inside
the cylinder and the piping. When the
air release is complete, operate the cylinder
at reduced pressure, then gradually
increase it to the normal operating
pressure.
5. Since Series CHQB does not have an
air release plug, release air from other
components (e.g. from piping, etc.) as
well.
6. When mounting the cylinder body with
mounting bolts, use the tightening torques
in the table at right as a guide.
7. Do not use two cylinders facing one
another horizontally or vertically in
such a way that their piston rods strike
each other.
8. When the cylinder head side contains
hydraulic fluid or is in a normally pressurized
condition, the applied load
must not be allowed to strike the piston
rod end. Avoid such applications.

产品留言

标题

联系人

联系电话

内容

验证码

点击换一张

注：1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!