CIT-03-04-50，YUKEN叶片泵参数[产品打印页面]

]资料

点击看大图

如果您对该产品感兴趣的话,可以

产品名称: CIT-03-04-50，YUKEN叶片泵参数
产品型号: CIT-03-04-50
产品展商: YUKEN
简单介绍
CIT-03-04-50，YUKEN叶片泵参数 The pollution control of hydraulic oil, and maintain the pollution level within the NAS 12 level. Note that if the PVL1 pump is started at a low speed of 950 r / min, the maximum fluid viscosity is limited to The maximum permissible deviation is less than 0.1 mm (.004 in.) TIR and maximum allowable error Less than 0.2 °. CIT-03-04-50，YUKEN叶片泵参数

CIT-03-04-50，YUKEN叶片泵参数的详细介绍

    CIT-03-04-50，YUKEN叶片泵参数
    企业QQ：2880626087
    电话；021-69001039
    手机；17321017802（微信）
    邮箱；17321017802@163.com
    联系人；周彩云
    地址：上海市嘉定区江桥嘉涌路99弄6号713室
    1. Type of hydraulic oil
    Oil base oil ........... U. Se R & O (rust and oxidation inhibitor) type oil or anti-wear type oil.
    In addition, use a 100 mm (150 mesh) fuel tank filter on the suction
    side and install a tank with a distance of more than 50 mm (2 inches).
    200mm 2 / s (910SSU).
    Description
    3. Pollution control
    (Equivalent to ISO VG-32 or 46)
    Note: Only oil base oil can be used for hydraulic oil.
    2. Recommended viscosity and oil temperature
    The viscosity range is 20-400 mm 2 / s (100-1800 SSU).
    , Directory number. EC-3001), or air is discharged by a slightly loose discharge side connection.
    When starting, run the pump as intermittently as possible without load.
    Use hydraulic oil that meets the recommended viscosity and oil temperature.
    Refer to the "Hydraulic Oil" section above for fluid viscosity at start-up.
    4. Other precautions
    If you are using a PVL1 series single pump at speeds below 1200 r / min,
    install the pump above the suction port
    Use a flexible coupling as much as possible and avoid any stress generated by bending or thrust.
    Hydraulic fluid contamination leads to pump failure and reduced pump life. adequate
    Axis alignment
    CIT-03-04-50，YUKEN叶片泵参数
    If the pump is installed on top
    The tank level is set below the oil level below 1.0 m (3.3 ft.).
    Oil temperature at 0 / + 70 ° C (32 - 158 ° F)
    So that the pump is easy to draw fluid at start-up.
    3. Start the note
    The pump may be difficult to draw fluid during initial operation or for a long period of rest.
    In this case, the exhaust valve should be pre-installed on the discharge side (model number ST1004 - - 10)
    2. Inhalation pressure
    The suction pressure is set at -20 to +30 kPa (5.9 in.Hg to +4.3 PSIG) at the pump inlet.
    In addition, use the suction pipe of the size shown in the dimension drawing.
    CIT-03-04-50，YUKEN叶片泵参数

产品留言

标题

联系人

联系电话

内容

验证码

点击换一张

注：1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!