如果您对该产品感兴趣的话,可以
产品名称:
G46-10--2M-C，SMC真空压力表
产品型号:
G46-10--2M-C
产品展商:
SMC
简单介绍
G46-10--2M-C，SMC真空压力表
(1) Before setting the (green) limit indicator, turn the
cover counterclockwise (approximately 6 to 7
mm) until it stops. Then, remove by pulling it towards
G46-10--2M-C，SMC真空压力表的详细介绍
G46-10--2M-C，SMC真空压力表
• Caution on handling: When drain or oil, etc. gets into the gauge, it may result in a malfunction.
Note 1) When mounting a pressure gauge, use caution not to tighten excessively. Excessive tightening will
cause product to be damaged. Use a pipe tape for sealing. Recommended tightening torque is
between 3 and 4 N·m for R 1/16 and 7 and 9 N·m for R 1/8.
注1）当安装一个压力表，请小心不要过度拧紧。拧得过紧会
导致产品故障。使用管道胶带密封。推荐的紧固扭矩：A：设置之间
7和9个N·M，R：12和14 N·M分别。
注2）当流体为水利用G46？-X3。接液部件均采用不锈钢结构。 （有些腐蚀
可被水造成的，因为这个产品的过流部件的材质有黄铜。）系统设计
不被水锤影响当使用水作为流体。类似地，当使用其它流体，
请向本公司确认的关于潜在的腐蚀性液体的兼容性信息。
注3）波登管和内部活动部件（齿轮等）的材质有黄铜，不无电 镀镍。这不是一个内部无铜产品。
Note 2) Water cannot be used as an operating fluid. Because the clearance gap of the air passage of the
Bourdon tube is very small. Water will block the gap and cause a malfunction.
Similarly, when using other fluids, please consult with SMC for fluid compatibility information
concerning possible corrosion and response delay, etc.
Note 1) When mounting a pressure gauge, use caution not to
tighten excessively. Excessive tightening will cause product to be damaged. Use a pipe tape for sealing.
Recommended tightening torque: R 1/8: Set between 7 and 9 N·m, R 1/4: 12 and 14 N·m respectively.
Note 2) When using other fluids, please consult with SMC for fluid compatibility
information concerning corrosive potential.
Note 3) Temperature conditions: at 20°C (±5°C), in other cases, ±6°C F.S.
注3 ）设定值或压力开关是通过指针（绿色表示） 。它的地步N.O.之间的电路（白）和
COM（黑色）被关断时压力下降。要设置的值，顺时针转动针在正确的位置，以
值。当设置;如果希望的设定位置已通过腿，转动针沿逆时针方向再返回
超出所需的值，然后再次在顺时针方向停止在希望的值返回针。值
而针行进在顺时针方向上必须设置。
(4) After completing the setting, replace the cover.
Fit the cover by aligning the cutout in the cover to
the groove on the top of the black case. Turn the
cover clockwise (approximately 6 to 7 mm) until it
stops. Make sure that the matching mark on the
cover is aligned with the groove on the top of the
注4 ）确保提供的0.1兆帕的设定压力和工作压力（包括之间的小差异
压降） 。如果差异较小，这可能会导致操作不当。参见662页上详细介绍了如何
载针。请小心：工作压力应该是针设定错误的压力之和
（±0.05兆帕） ，滞后（ 0.07兆帕） ，并在设定的压力值，或者该电路的显示精度（± 0.05兆帕）
N.O.之间（白）和COM（黑色）可能无法打开，而压力增加。
注5 ）误差值：加0:03兆帕的压力表指针错误针设定错误。
3) After completing the setting, replace the cover.
Fit the cover by aligning the cutout in the cover to
the groove on the top of the black case. Turn the
cover clockwise (approximately 6 to 7 mm) until it
stops. Make sure that the matching mark on the
cover is aligned with the groove on the top of the
