如果您对该产品感兴趣的话,可以
产品名称:
KQ2V06-01AS，进口SMC防静电快换接头
产品型号:
KQ2V06-01AS
产品展商:
SMC
简单介绍
KQ2V06-01AS，进口SMC防静电快换接头
当自动开关接通的车内磁铁的位置之间的范围
切换单元移动和那里的开关断开的磁铁移动相同的位置
方向。 当自动开关接通的车内磁铁的位置之间的范围
切换单元移动和那里的自动开关关闭，因为磁铁的位置的移动 相反的方向。
KQ2V06-01AS，进口SMC防静电快换接头的详细介绍
KQ2V06-01AS，进口SMC防静电快换接头
Note 1) Mounting of the stopper ring shown in Examples 2, 3, and 4 are not applicable for size 10.
Note 2) • marks in the illustrations above indicate the position of the stopper ring assembly.
Note 3) Select the appropriate rotation of the rotary actuator by itself after careful consideration of the
content of “installation of angle adjuster”.
Note 4) For size 40, each block comes with 2 holding bolts.
注1）由于旋转调整范围的角度将
限于通过旋转当使用旋转致动器为90°时，使
一定要考虑到这一点订货时。旋转驱动器
90应该被用来调整为85 °或更小的角度比
注2）连接端口侧端口只。
注3 ）允许动能是一样的规格或
取下盖子树脂在下面的插图，在滑动闭锁块
长槽和锁定到'适当位置，以调整旋转
位置和旋转。突出4倒角的扳手上的输出
该轴旋转允许手动操作，方便定位。
Lock block in Fig. 1-2, and move block clockwise to allow the rotation
of the shaft with single flat in Fig. 1-1 from point zero to end of rotation q.
When block is locked and block is moved counterclockwise, the shaft
with single flat in Fig. 1-1 rotates from point zero to end of rotation w. The
maximum rotation range of the shaft with single flat is as follows: Sizes 10,
40: up to 230°; Sizes 15, 20, 30: up to 240° (Fig. 1-2 shows when the rotation
（请参考下页的详细信息中的旋转设置的例子。 ）
虽然人们挡块安装在麋鹿长槽的标准
角度调节范围当2止动块被安装在一个单一的
The maximum rotation range of the shaft with single flat in Fig. 2-2 is 195°,
from end of rotation q to end of rotation w. The rotation range decreases
to the range between end of rotation w and e as in 2-1 when moving block
in Fig. 2-2 clockwise, and similarly when block is moved
counterclockwise, the rotation range decreases to the range between end
rotation q and r. However, since the internal stopper will come into
contact with the vane at end of rotation q in Fig. 2-1, make sure that the
stopper lever stops at block when adjusting.
正如<figure B> ， pcs.stopper显示当在**台PC安装两个街区。
长槽，带旋转麋鹿阻挡块（ A）（B ） ，或旋转范围
用单平面（key）的输出轴是可调节的，如<图中描述
一> ，无论是在50 °和60°对端口A和B （旋转范围左
单平（键）当安装2个。在另一侧的止动块
槽是从<figure A>的对面，可设定范围内
无论是右50 °，对端口A和B
