如果您对该产品感兴趣的话,可以
产品名称:
AL40-N04+Y400T，日本SMC油雾器
产品型号:
AL40-N04+Y400T
产品展商:
SMC
简单介绍
AL40-N04+Y400T，日本SMC油雾器
The rotation axis is reversed.
The long shaft and short shaft are shortened.
shortening the shaft is not required, indicate “.” for
AL40-N04+Y400T，日本SMC油雾器的详细介绍
AL40-N04+Y400T，日本SMC油雾器
仅通过调整差压就可轻松实现给油量设定。
通过开关给油塞可在不停止通气的情况下实现补油。
可通过给油孔观察到微雾的产生情况。
Symbol: A43 Applicable to single vane type only
A special end is machined onto both the long and short shafts, and a through-hole is
drilled into both shafts. Female threads are machined into the through holes, whose
diameter is equivalent to the diameter of the pilot holes.
• The maximum dimension L1 is, as a rule, twice the thread size.
• Applicable shaft types: K, T • Equal dimensions are indicated by the same marker.
Symbol: A44 Applicable to single vane type only
可通过升压器提供高于主空气通路的压力，
这个压差可以看做是油雾产生的压差，因此主空气通路的压力下降很少。
仅通过调整油雾产生的压差达到微雾恒定供给。
通过开关给油槽可在不停止通气的情况下实现补油。
可通过给油孔观察到微雾的产生情况。
A special end is machined onto both the long and short shafts, and a through-hole is
drilled into both shafts. Female threads are machined into the through-holes, whose
diameter is equivalent to the diameter of the pilot holes
• The maximum dimension L1 is, as a rule, twice the thread size.
• Applicable shaft types: J, X, Z • Equal dimensions are indicated by the same marker.
Symbol: A39 Applicable to single vane type only
?Minimum machining diameter for d1 is 0.1.
?Applicable shaft types: S, Y
从油箱和喷雾器的开关控制部分将油和空气传送到混合阀。
LMV 混合阀 因内置有油针阀和空气针阀，
在油雾喷射单元对油量和空气量进行调整
，然后同时由喷嘴喷出。
LMH 磁石保持座 支架前端装有混合阀，
可自由安装在机床等机械的钢铁部分。
LMD 分支管 在使用多个混合阀的场合，
用于将来自油雾喷射单元的油和气体分开。
Symbol: A41 Applicable to single vane type only
?Minimum machining diameter for d1 is 0.1.
?Applicable shaft types: J, X, Z
Symbol: A40 Applicable to single vane type only
Shaft with through-hole
?Minimum machining diameter for d1 is 0.1.
列/CAD 接管口径 1次給油量 (cm3)
ALIP 压力型 1/8 0～0.04
ALT10 油箱 气：1/8
油：1/4 油箱容量： 160cm3
ALT20 油箱容量：1000cm3
特长 在润滑点之前直接供给一定量的油。
能够为润滑油不容易到达的回路或空气消耗量小的场合提供可靠的定量供油。
?Applicable shaft types: K, T
Symbol: A42 Applicable to single vane type only
A special end is machined onto both the long and short shafts, and a through-hole is
drilled into both shafts. Female threads are machined into the through-holes, whose
diameter is equivalent to the diameter of the pilot holes.
?The maximum dimension L1 is, as a rule, twice the thread size.
?Applicable shaft types: S, Y ?Equal dimensions are indicated by the same marker.
