美国ASCO微型电磁阀，ASCOAL系列通用微型阀[产品打印页面]

]资料

点击看大图

如果您对该产品感兴趣的话,可以

产品名称: 美国ASCO微型电磁阀，ASCOAL系列通用微型阀
产品型号: -
产品展商: ASCO
简单介绍
美国ASCO微型电磁阀，ASCOAL系列通用微型阀 D6 ON/OFF CLEANING CYCLE BY EXTERNAL VOLT FREE CONTACT If contact D6 is open, the cleaning cycle is not enabled and the display shows 'OFF'.

美国ASCO微型电磁阀，ASCOAL系列通用微型阀的详细介绍

美国ASCO微型电磁阀，ASCOAL系列通用微型阀
或者DP读数不是0.00千帕，可以通过按键A和C调整它没有连接风管
C13_10差压读数FULL RANGE 10千帕
长压差测定序10.00千帕= 100.0毫巴= 1012毫米水柱。
带有DP阅读超过10千帕，显示屏显示“E”代替DP的数值。
风扇停止后D1ab1额外的后清洗周期
在设定您可以选择旨在管理风扇和后洗涤循环模式：
SET = 0 （不使用选项C11A avaliable ）
如果您连接的电路无电压辅助触点用于驱动风扇的定时器，你可以添加一个预先设定的号码
后风扇停止。它们的数量可以从键盘被设置为从0到99。
后清洗周期可以同时激活时， C6触点断开。
如果D1a相触点断开，显示屏将显示“ -0 - '和信号的周期不工作，因为风扇是关闭的。
显示屏上的小数点会在风扇停止后的周期闪烁和关闭。
注意D1a相：连接D1a相通过的跳跃装置，如果它不具有活性的输入（见F01 ）使用。
C3 DIFFERENTIAL PRESSURE READING BY INTERNAL TRANSDUCER (max 10 kPa)
C7d1 MAXIMUM dP ALARM WITH ALARMED OPEN CONTACT AND AUTOMATIC RESET
If the dP readout is above the threshold in Set up, the maximum dP alarm is activated. The display shows the alarm condition
description) or the dP readout and letter H alternatively, according to the model.
The corresponding alarm relay will signal its condition. The alarm is automatically reset when the dP readout is below the The activation of this alarm is delayed by 20 seconds by default.
In this set up code it is possible to adjust the zero reading of differential pressure. In this function the display shows the dP
If the dP control is activated, you can add a pre-set number of washing cycles after the fan stop. Their number can be set from
99. The Timer will automatically recognise the fan state by comparing the dP readout with a 0.20 kPa fixed threshold: dP >
Post-cleaning cycles will be activated even if the dP readout = 0.
If the fan is off, the display will show '-0-'.
The decimal points on the display will flash on and off during the additional cycles.
Post-cleaning cycles will be activated only if the dP readout should reach the cycle STOP threshold value during the normal
NOTE D6: Use a jumper for D6 if it is not used with active inputs (see F01).
G1 MAXIMUM LOAD POWER FOR 25W OUTPUT FOR MAX 5 SEC.

产品留言

标题

联系人

联系电话

内容

验证码

点击换一张

注：1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!