主营产品:阀门、气动元件、仪器仪表、电子元器件
产品[

SMC排气洁净器,AMC220-02B[产品打印页面]

]资料
如果您对该产品感兴趣的话,可以
产品名称: SMC排气洁净器,AMC220-02B
产品型号: AMC220-02B
产品展商: SMC
简单介绍
SMC排气洁净器,AMC220-02B 排气洁净器 AMC 系列/CAD 特长 AMC 消声效果35dB (A) 油雾回收率:99.9%以上。 SMC排气洁净器,AMC220-02B

SMC排气洁净器,AMC220-02B的详细介绍

SMC排气洁净器,AMC220-02B

电话:O21-3952 9829/3O-8O1O
传真:O21-6O83 1959
手机:189 1857 2467
Q:125 5O9 6653
联系人:张海情
邮箱:8010@shqiantuo.com.cn

排气洁净器  AMC
系列/CAD 特长
AMC  消声效果35dB (A)
油雾回收率:99.9%以上。

如何选择条件:在工作压力0.5兆帕
排水排水指南
流量特性(初始条件)
根据要使用的电路消耗的空气中选择一个模型。
1。获取要使用的致动器的空气消耗量。但是,如果一个
将集中管道式排气净化器的使用,总结空气
消耗的致动器同时操作。还添加了
从气缸的管路的EXH容量。
2。选择一个模型,该模型提供了的处理流量,
超过在步骤1中得到的消费量。
如何读AMC510图:如果是工作在流量为
1000升/分钟(ANR),入口压力0.05MPa的

设计
警告
1。可能成为阻塞排气口的堵塞
排气清洁。
因此,请确保提供一个安全的设计,以免
导致整个系统出现故障。
2。中得到的流量特性的进气压力
消音器的曲线图表示的压力(P1)之前,
排气清洁。 (参见下图)。
3。如果压缩空气从电磁阀排出
不干净的堵塞可能发生,
4。的背面的压力(入口压力)为0.1MPa,或工作在
以下。
选择
慎重
1。选择一个排气这是能够出售的清洁剂
允许的通流容量压缩空气
从电磁阀排出。
如果流量超过允许流的排气
清洁剂,排水和油到环境中,也可喷涂
造成设备损坏。
2。选择一个模式,有一个更大的有效面积比
电磁阀的(包括化合物有效面积)。
3。如果这与中央管道系统中,将被用来
包括计算峰值耗气量
同时执行,执行器
连接的管道的容量。
然后,选择一个模式,使计算的值将是
小于的流量的排气
清洁剂。 (选择一种样式,有足够的能力,因为
当元素变得排气速度会降低
堵塞。)
安装
慎重
1。确保不适用的横向负荷期间身体或
在安装之后。
2。采取预防措施,使管道的负载不适用
到主体。
附加的支架是支撑排气清洁
仅机身。因此,它不能支持的管道或其它项目。如果
这些产品需要得到支持,提供额外的
支持。
3。必须垂直安装排气洁净。
如果它被安装对角,横向,或倒置的油,
相隔元素会溅到周围的环境。
保养
慎重
1。如果排气速度下降,系统的性能
减少因堵塞,更换一个新的元素。
执行机构的经营状况,一定要核实
至少每天一次。
2。元件的更换时间间隔为前
在排气过程中的内部压力达到0.1兆帕或之后
1年的运作,以先到者为准。
•提供一个分支上的电源侧排气清洁
安装一个阀门和一个压力表。
•在检查过程中,打开阀门,并检查压力
排气排放的时间。
(阀门必须保持关闭状态,除了检查。
可以打破,如果压力表阀门保持开放。)

SMC排气洁净器,AMC220-02B

Design
Warning
1. The exhaust port could become blocked by the clogging
of the exhaust cleaner.
Therefore, make sure to provide a safe design so as not to
cause the whole system to malfunction.
2. The inlet pressure obtained in the flow characteristic
graph of silencer indicates the pressure (P1) prior to
exhaust cleaner. (Refer to the diagram below.)
3. If compressed air exhausted from the solenoid valve is
not clean clogging may occur,
4. Operate at a back pressure (inlet pressure) of 0.1 MPa or
less.
Selection
Caution
1. Select an exhaust cleaner which is able to dispose of the
maximum allowable flow capacity of compressed air
exhausted from solenoid valve.
If the flow exceeds the maximum allowable flow for the exhaust
cleaner, drainage and oil may be sprayed into the environment
causing damage to equipment.
2. Select a model which has a bigger effective area than that
of the solenoid valve (including compound effective area).
3. If this will be used with a centralized piping system,
calculate the peak maximum air consumption by including
the actuators that operate simultaneously and the
capacity of the piping that is connected.
Then, select a model so that the calculated value will be
less than the maximum flow volume of the exhaust
cleaner. (Select a style with ample capacity because the
exhaust speed will decrease when the element becomes
clogged.)
Mounting
Caution
1. Make sure not to apply a lateral load to the body during or
after the installation.
2. Take precautions so that the piping load is not be applied
to the main body.
The attached bracket is for supporting the exhaust cleaner
body only. Thus, it cannot support the piping or other items. If
these items need to be supported, provide an additional
support.
3. Exhaust cleaner must be mounted vertically.
If it is mounted diagonally, laterally, or inverted, the oil that is
separated by the element will splash on the surroundings.
Maintenance
Caution
1. If the exhaust speed drops and the system performance
decreases due to clogging, replace with a new element.
Make sure to verify the operating condition of the actuator at
least once a day.
2. The replacement interval for the element is before the
internal pressure during exhaust reaches 0.1 MPa or after
1 year operation, whichever comes first.
• Provide a branch on the supply side of the exhaust cleaner to
mount a valve and a pressure gauge.
• During inspection, open the valve and check the pressure at
the time of exhaust discharge.
(The valve must remain closed except for inspection. The
pressure gauge could break if the valve remains open.)

SMC排气洁净器,AMC220-02B

产品留言
标题
联系人
联系电话
内容
验证码
点击换一张
注:1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!


上海乾拓贸易有限公司    地址:上海嘉定嘉涌路99弄6号713    邮编:
联系人:单先生    电话:021-69000975   手机号码:18918574312    传真:021-39947181
沪ICP备09006758号-2  
 

沪公网安备 31011402005013号

点击这里给我发消息 点击这里给我发消息 点击这里给我发消息 点击这里给我发消息 点击这里给我发消息 点击这里给我发消息 点击这里给我发消息