费斯托空隙传感器，SOPA-CM1H-R1-WQ6-2P-M12[产品打印页面]

 费斯托空隙传感器，SOPA-CM1H-R1-WQ6-2P-M12

电话：O21-3952 9829/3O-8O1O
传真：O21-6O83 1959
手机：189 1857 2467
QQ：125 5O9 6653
联系人：张海情
邮箱：8010@shqiantuo.com.cn

特性  特性
  标准产品
 
授权   
CE 符号 (参见符合的标准)   
材料备注  
符合 RoHS
测量原则   
传感器范围   
工作压力   
工作介质   
关于工作和先导介质的说明   
环境温度   
Repetition accuracy of switching point  
±5 µm sensing range 20 to 200µm
输出电流   
短路强度   
工作电压范围 DC   
极性容错保护   
电连接  
M12x1
插头
符合EN 60947-5-2标准
圆形设计
安装类型  
带通孔
带高帽式导轨
墙面/表面固定
气动连接   
产品重量   
外壳的材料信息   
显示类型   
设定选项  
通过显示装置和按钮
防止误操作   
防护等级  
to IEC 60529

费斯托空隙传感器，SOPA-CM1H-R1-WQ6-2P-M12

 The following notes must be observed
when lubricated compressed air is used:
• Use Festo special oil OFSW-32 or the
alternatives listed in the Festo
catalogue (as specified in
DIN 51524-HLP 32; basic oil viscosity
32 cSt at 40 °C).
• If lubricated compressed air is used,
additional lubrication must not exceed
25 mg/m3 (ISO 8573-1:2010). The
quality of compressed air downstream
of the compressor must correspond to
that of unlubricated compressed air.
• The lifetime lubrication required for
unlubricated operation can be
"flushed out" when products are operated
using lubricated compressed air.
This can result in malfunctions if a system
is switched back to unlubricated
operation after lubricated operation.
• The lubricators should, where possible,
always be installed directly
upstream of the cylinders used in order
to prevent operating the entire system
with lubricated air.
• Never over-lubricate the system. To determine
the correct lubricator settings,
the following "oil form test" can be implemented:
hold a piece of white card
approx. 10 cm away from the exhaust
port (without silencer) of a working
valve of the most distant cylinder. Allow
the system to work for some time,
the card should only showa pale yellow
colouration. If oil droplets appear,
this is an indication that too much oil
has been used.
• The colour and condition of the exhaust
silencer provide further evidence
of over-lubrication. Marked yellow
colouration and dripping oil indicate
that the lubrication setting is too high.
• Dirty or incorrectly lubricated
compressed air will reduce the service
life of the pneumatic components.
• Service units must be inspected at
least twice a week for condensate and
correct lubrication settings. These
inspections should be included in the
machine maintenance plan.
• To protect the environment, as little
lubrication as possible should be
used. Festo pneumatic valves and
cylinders have been constructed in
such a manner that, under permitted
operating conditions, additional
lubrication is not required and yet

A differentiation must be made between
residual oil for operation with unlubricated
air and additional oil for operation
with lubricated air.
Unlubricated operation:
Examinations involving residual oil content
have revealed that the various types
of oil have entirely different effects. For
this reason, a distinction must be made
between the following oil types when
analysing the residual oil content:
• Bio-oils: oils based on synthetic or
natural ester (e.g. rapeseed oil methyl
ester). In this case, residual oil content
must not exceed 0.1 mg/m3.

费斯托空隙传感器，SOPA-CM1H-R1-WQ6-2P-M12

产品留言

标题

联系人

联系电话

内容

验证码

点击换一张

注：1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!